Miele G 5481 Operating Instructions Manual Download Page 70

Page: 70 / 92

Cleaning and care

Cleaning the drain pump

If water remains in the wash cabinet
after the end of a programme, the water
has not been pumped away. The drain
pump may be blocked by foreign
objects. These foreign objects are easy
to remove.



Disconnect the dishwasher from the
power supply.
To do this, switch off at the socket
and withdraw the plug.



Take the filter combination out of the
wash cabinet (see “Cleaning and care
- Cleaning the filters”).



Scoop the water out of the wash
cabinet using a suitable container or
utensil.



Press the catch of the drain pump
cover inwards





Tip the cover inwards until it is
released





Rinse the cover thoroughly under
running water and remove all foreign
objects.

Summary of Contents for G 5481





























































































Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands

Miele G 5481, Operating Instructions Manual

Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands