Miele G 5481 Operating Instructions Manual Download Page 15

Page: 15 / 92

Warning and Safety instructions

Transport



Damage to the dishwasher can compromise your safety. Before

using the dishwasher, check it for any visible transport damage.
Never use a damaged dishwasher.



Only transport the dishwasher in an upright position so that no

water flows into the electrical controls, as this would cause faults.



If you wish to transport the dishwasher, empty it and securely

fasten all loose parts such as baskets, hoses, and cables.

Disposal of your old dishwasher



Make the door lock inoperative so that children cannot

accidentally shut themselves in. Remove or destroy the locking
bracket of the door lock, and make appropriate arrangements for the
disposal of the appliance.

Summary of Contents for G 5481





























































































Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands

Miele G 5481, Operating Instructions Manual

Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands