Miele G 5481 Operating Instructions Manual Download Page 65

Page: 65 / 92

Cleaning and care

Removing the upper spray arm



Push the upper spray arm upwards



to engage the inner ratchet. Then
unscrew the spray arm by rotating the
screw thread anti-clockwise (when
viewed from below)



Removing the middle spray arm



Rotate the screw thread of the middle
spray arm clockwise (overhead
perspective)



(see diagram) and

remove the spray arm



Removing the lower spray arm



Remove the lower basket.



Rotate the screw thread of the lower
spray arm anti-clockwise



and pull

the spray arm upwards to remove



Cleaning the spray arms



Use a pointed object to push food
particles stuck in the jets into the
spray arm.



Rinse the spray arm thoroughly under
running water.

Summary of Contents for G 5481





























































































Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands

Miele G 5481, Operating Instructions Manual

Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands