Miele G 5481 Operating Instructions Manual Download Page 44

Page: 44 / 92

Detergents

Adding detergent



Lift the yellow catch on the lid of the
detergent compartment



The lid will open.
The lid will also be open at the end of
the programme.



Add the detergent to the detergent
compartment.



Slide the lid shut until you hear it click
into place.

The detergent must not cause the
detergent compartment lid to get
stuck. This can prevent the lid from
opening during the programme
sequence.
Do not overfill the detergent
compartment.



Ensure that the detergent packaging
is properly closed after use. This
prevents the detergent from getting
damp and clumping together.



You can also apply a small amount of
detergent to the inner panel of the
door in programmes that have a pre-
wash stage (see “Programme chart”).

Summary of Contents for G 5481





























































































Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands

Miele G 5481, Operating Instructions Manual

Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands