Miele G 5481 Operating Instructions Manual Download Page 58

Page: 58 / 92

Programme options

Switching off the refill
reminders

If you only ever use combination
detergent products containing salt and
rinse aid in your dishwasher, you can
switch off both refill reminders if you
wish.



Open the door.



Switch the dishwasher off with the



button, if it is switched on.



Press the



button in and,

while

holding it in

, switch the dishwasher

on using the



button.

Keep the



button pressed in for at

least 4 seconds until the



indicator

light comes on.

If this does not happen, start the
procedure from the beginning again.



Press the



programme selection

button 9 times.

The top left programme indicator light
will flash rapidly 9 times at intervals.

The flashing sequence in the time
display will show whether the refill
reminders are switched on or off.

 

: Refill reminders activated

 

: Refill reminders deactivated



Press the



button to change the

setting.

The setting is now stored in memory.



Switch the dishwasher off with the



button.

Please make sure that if you stop
using combination detergents, you
refill the dishwasher salt and rinse
aid. Switch the refill reminders back
on.

Summary of Contents for G 5481





























































































Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands

Miele G 5481, Operating Instructions Manual

Search results

Summary of Contents for G 5481

Reviews:

Related manuals for G 5481

Brands by name

Popular brands