background image

Troubleshooting - 15

Video Troubleshooting, 

continued

SYMPTOM

CAUSE

REQUIRED ACTION

 Picture is too narrow

Maladjusted WIDTH
pot

From Diagnostic Menu select MONITOR TEST.
Watch Crosshatch Screen while adjusting
WIDTH pot for best picture. You’ll find this pot on
Monitor Remote Control Board, behind coin door.

 Picture is too short

Maladjusted HEIGHT
pot or damaged
vertical circuit

1. From Diagnostic Menu select MONITOR TEST.

Watch Crosshatch Screen while adjusting
HEIGHT pot for best picture. You’ll find this pot
on Monitor Remote Control Board, behind coin
door.

2. If pot has no effect, service vertical output circuit.

 Picture seems shifted to one

side

Maladjusted
HORIZONTAL
POSITION pot

From Diagnostic Menu select MONITOR TEST.
Watch Crosshatch Screen while adjusting
HORIZONTAL POSITION pot for best picture.
You’ll find this pot on Monitor Remote Control
Board, behind coin door.

 Keystone-shaped picture

Shorted turns in yoke

1. Substitute working yoke.
2. Have service bureau converge monitor.
3. Retest monitor.

 Blotches of color appear on

screen

Picture tube aperture
mask is magnetized

Demagnetize monitor with external degaussing
coil. Take care not to magnetize neighboring
games. Monitor may be left on or off during this
procedure.

 White areas in center of

screen appear tinged with
color

 Object edges have fringe of

one or more colors

Picture tube purity or
static convergence is
out of alignment

1. Turn on Video Game Machine (VGM).
2. Press and hold TEST MODE to enter Menu

System. Select Diagnostic Menu from the Main
Menu. Select MONITOR TEST. Perform tests for
Crosshatch, Red, Green and Blue screens to find
clearest display of problem.

3. Display screen with the most severe problem.
4. Display Crosshatch Screen. Locate purity and

static convergence ring magnets on back of
monitor neck. Watch screen in mirror. Adjust
magnets to minimize problem. Follow
instructions from monitor manufacturer.

5. Display Crosshatch Screen. Touch up

adjustments while watching screen in mirror.

CAUTION

Do not remove or install any connector when power is turned on. Installation under
power will damage the circuit boards or hard disk drive and void the warranty.

Summary of Contents for Cruis'n Exotica














































































































Reviews: