background image

 9

ELECTRICAL  WORK

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

C: Putting nut on

     Remove flare nuts attached to indoor and 
     outdoor unit, then put them on pipe/tube 
      having completed burr removal.(not possible
      to put them on after flaring work) 

Flare nut

Copper tube

Fig.18

Fig.19

D: Flaring work

    Firmly hold copper pipe in a die in the 
    dimension shown in the table below.

Caution

Align the center of the pipes.
Sufficiently tighten  the flare 
 nut with fingers, and then tighten
 it with a spanner and torque wrench
 as shown in Fig.20 & 21.

Tightening Connection

Excessive  torque can  break nut 
depending on installation conditions.

Fig.21

Indoor unit tubing

Flare nut

Pipings

Fig.20

Electric safety regulations for the initial Installation
1. If there is serious safety problem about the power supply, the technicians should refuse
    to  install the air conditioner and explain to the client until the problem is solved. 
2. Power voltage should be in the range of 90%~110%of rated voltage.
3. The creepage protector and main power switch with a 1.5 times capacity of Max. Current
    of the unit should be installed in power circuit.
4. Ensure the air conditioner is grounded well.

 
7. An individual branch circuit and single receptacle used only for this air conditioner must be 
    available. See the following table for suggested wire sizes and fuse specifications:

5. According to the attached Electrical Connection Diagram located on the panel of the outdoor

   unit to connect the wire.

6. All wiring must comply with local and national electrical codes and be installed

   by qualified and skilled electricians.  

Electrical work

Outer diam.

(mm)

A(mm)

Max.

Min.

6.35

1.3

0.7

9.52

1.6

1.0

12.7

1.8

1.0

12.7

16

1.8

2.4

1.0

2.2

Outer

diam.

Tightening

torque(N.cm)

Additional tightening

torque(N.cm)

6.35

12.7

16

9.52

1500

(153kgf.cm)

1600

(163kgf.cm)

3500

(357kgf.cm)

3600

(367kgf.cm)

2500

(255kgf.cm)

2600

(265kgf.cm)

4500

(459kgf.cm)

4700

(479kgf.cm)

Summary of Contents for INVERTER SPLIT TYPE ROOM AIR CONDITIONER

















Reviews: