background image

11

ELECTRICAL  WORK

Warning

Be sure to comply with local codes while 
running the wire from the indoor unit to
the outdoor unit.
Every wire must be connected firmly.
No wire should be allowed to touch
refrigerant tubing, the compressor 
or any moving parts.
Loose wiring may cause the terminal to
overheat or result in unit malfunction. 
A fire hazard may also exit. Therefore,
be sure all wiring is tightly connected.
Disconnecting means must be provided 
and shall be located within sight from and 
readily accessible from the air conditioner.
Connecting cable with conduit shall go 
 through the hole of the conduit panel.

Note : 

To prevent wires loosening or leaving

 the Cord Clamp, please select proper cord
 diameter to fill the holes on the cord clamp.

Power supply 
cord

Power supply 
1

φ

 208-230V~60Hz

Special branch circuit breaker
(Fuse/Breaker capacity:20A)

Terminal block of outdoor unit

To indoor unit

To indoor unit

To indoor unit

To power supply

To power supply

To power supply

Fig.23b

L1   L2    S    L1   L2

1(L) 2(N)  S     L      N

L1   L2    S    L1   L2

(1)

(2)

(3)

Summary of Contents for INVERTER SPLIT TYPE ROOM AIR CONDITIONER

















Reviews: