Microgard 801-G02, Instructions For Use Manual

Page: 5 / 134

Property Test Method
Minimum Performance
Class Required For EN943-
2:2002
MICROCHEM
®
6000
Performance Class
Abrasion resistance EN 530 4 of 6 6 of 6
Flex cracking resistance EN ISO 7854 1 of 6 1 of 6
Flex cracking resistance at
low temperatures (-30°C)
EN ISO 7854 (-30°C) 2 of 6 2 of 6
Trapezoidal tear resistance EN ISO 9073-4 3 of 6 3 of 6
Tensile Strength EN ISO 13934-1 4 of 6 4 of 6
Puncture resistance EN 863 2 of 6
*
2 of 6
Resistance to Ignition EN 13274-4 Pass Pass
Resistance to flame EN 13274-4 1 of 3 2 of 3
Seam strength EN ISO 13935-2 5 of 6 5 of 6
MICROCHEM
®
6000 Fabric EN14126: 2003 Results
Test Method EC Classification
ISO/FDIS 16603 Resistance to penetration by blood/fluids under pressure Pass 20 kPa
ISO/FDIS 16604 Resistance to penetration by blood borne pathogens 6 of 6
EN ISO 22610 Resistance to wet bacterial penetration (mechanical contact) 6 of 6
ISO/DIS 22611 Resistance to biologically contaminated aerosols 3 of 3
ISO/DIS 22612 Resistance to dry microbial penetration 3 of 3
PERFORMANCE CLASS ACCORDING TO EN 943-2
Test Method
*
Physical
State
Chemical
MICROCHEM
®
6000
Visor Ansell Barrier
Glove
*
ETCHE
Boot
*
EN ISO 6529 Liquid Dichloromethane (DCM) 6 of 6 4 of 6 2 of 6 2 of 6
EN ISO 6529 Liquid Methanol 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid n-Heptane 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Toluene 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Diethylamine 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Sodium Hydroxide (40%) 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Sulphuric Acid (96%) 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Gas Ammonia 6 of 6 6 of 6 0 of 6 **
3 of 6
EN ISO 6529 Gas Chlorine 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Gas Hydrogen Chloride 6 of 6 6 of 6 5 of 6 3 of 6
EN ISO 6529 Liquid Acetone 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Acetonitrile 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Ethyl Acetate 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Carbon Disulfide 6 of 6 6 of 6 6 of 6 3 of 6
EN ISO 6529 Liquid Tetrahydrofuran (THF) 6 of 6 6 of 6 6 of 6 3 of 6
MICROCHEM
®
6000 chemical permeation testing (Permeation Resistance)
Physical performance of MICROCHEM
®
6000
TECHNICAL SPECIFICATIONS
4
* Gloves and Boots tested according to EN 374-3.
Note: For information on the permeation resistance and mechanical performance of the outer glove please refer to the glove manufacturers instruction for use document. A copy of which is
provided with each suit.
** ATTENTION! According to EN 943-2, as Class 2 of 6 was not achieved the glove is not suitable for use against this chemical under continuous exposure. Wearers are therefore advised if
continuous exposure to this chemical is expected then an additional outer glove should be selected which achieves at least Class 2 according to EN 943-2 requirements. For advice please
contact Microgard Ltd.
*
According to EN 943-2, when only the minimum performance requirement (Class 2 of 6) for puncture resistance is achieved the reader should be advised that the chemical protective
clothing may not be suitable for use where there is a high risk of puncture.