Page 35
Appendix | GenICam surfaceCONTROL Parameters | Version 1.5
surfaceCONTROL 3D SC2500 / SC2510
Name
Description
Documentation Text
Device Control
DeviceTemperatureSelector
Selects the location within
the device, where the
temperature will be mea-
sured.
Serves as a switch for the temperature sensor to be read:
Internal - internal sensor temperature
Cpu - processor temperature
CpuBoard - temperature of processor’s circuit board
LED - LED temperature
CameraSensorBoard1 - internal temperature of camera #1
CameraSensorBoard2 - internal temperature of camera #2
DeviceTemperature
[DeviceTemperatureSelector]
Device temperature in
degrees Celsius (C).
Temperature of the component selected in DeviceTemperatureSelec-
tor.
Source Control
SourceSelector
Selects the source to
control.
Serves as a switch for the data source to be configured:
- Source0: Virtual source for 3D measured data
- Source1: Camera 1
- Source2: Camera 2
Image Format Control
RegionSelector
Selects the Region of
interest to control.
Serves as a switch for the parameters to describe the measuring field.
Note that this switch also depends on the SourceSelector. The follow-
ing settings are possible:
- Region0: Describes the measuring field of the cameras [Source1] or
[Source2]
- Scan3dExtraction0: Describes the 3D measuring field [Source0]
Width[SourceSelector]
[RegionSelector]
Width of the image pro-
vided by the device (in
pixels).
The number of pixels in u-direction in the camera image [Region0].
For [Scan3dExtraction0] the parameter specifies the number of 3D
points in x-direction.
The following combinations of SourceSelector and RegionSelector are
permissible:
- [Source0][Scan3dExtraction0]
- [Source1/Source2][Region0]
Height[SourceSelector]
[RegionSelector]
Height of the image
provided by the device (in
pixels).
The number of pixels in v-direction in the camera image [Region0].
For [Scan3dExtraction0] the parameter specifies the number of 3D
points in x-direction.
The following combinations of SourceSelector and RegionSelector are
permissible:
- [Source0][Scan3dExtraction0]
- [Source1/Source2][Region0]
PixelFormat[SourceSelector]
[RegionSelector]
[ComponentSelector]
Format of the pixels pro-
vided by the device.
Indicates the pixel format used for the selected component. Pixel for-
mats Mono8 and Mono16 are available for the [Intensity] components.
You can select Mono16 or Coord3D_C32f for the 3D data [Range].
ComponentSelector
[SourceSelector]
[RegionSelector]
Selects a component to
activate/deactivate its data
streaming.
The following entries are available:
- Intensity: Live camera image
- Range: 3D data
- Confidence: Mask for invalid points in 3D data
The following combinations of SourceSelector, RegionSelector and
ComponentSelector are permitted:
- [Source0][Scan3dExtraction0][Range]
- [Source0][Scan3dExtraction0][Confidence]
- [Source1/Source2][Region0][Intensity]
ComponentEnable
[SourceSelector]
[RegionSelector]
[ComponentSelector]
Controls if the selected
component streaming is
active.
Describes the components to be transmitted. It is used in particular
to distinguish between setup operation (live mode) and measurement
mode. Setup operation is enabled, if only the [Intensity] component is
enabled.
ImageScale[SourceSelector]
[ComponentSelector]
2D Mode components
only: Scale
Scaling factor for the gray values of the [Amplitude], [Curvature] and
[Base] components.
Summary of Contents for surfaceCONTROL SC2500
Page 4: ...surfaceCONTROL 3D SC2500 SC2510...
Page 41: ......
