MHSC LLCF36 Installation And Operating Instructions Manual Download Page 6

6

79D0004

Lo-Rider Designer Vent Free Fireboxes

Firebox framing can be built before or after the appliance is set 
in place. Construct firebox framing following 

Figures 9 through 

14 on pages 9 and 10 

for your specific installation requirements. 

Refer to Figure 1 on Page 5 

for firebox dimensions. The framing 

headers may rest on the top of the firebox standoffs.
The firebox may be installed directly on a combustible floor or 
raised on a platform of an appropriate height. Do not place firebox 
on carpeting, vinyl, or other soft floor coverings. It may, however, 
be placed on a flat wood, plywood, particle board, or other hard 
surfaces.  Be  sure  firebox  rests  on  a  solid  continuous  floor  or 
platform with appropriate framing for support so that no cold air 
can enter room from under the firebox. 
The classification “noncombustible material” includes, but is not 
limited to: stone, brick, and mortar. Noncombustibles are safe to 
overlay the black-painted metal face, including radiant plates, and 
do not pose a fire hazard. Any noncombustible finish material must 
not extend past or interfere with the fireplace opening.
The classification “combustible material” includes, but is not lim-
ited to: plywood, drywall, and particle board. Combustible materi-
als may contact the sides, bottom, or back of the firebox.  Do not 
overlay the black painted face with combustible materials.

fireplaCe framinG 

Figure 10 - 
Top View of Framing Specifications for 
Corner Units (Model LRCF36/LLCF36)

Figure 9 - 
Top View of Framing Specifications 
for Peninsula Units (Model LPF36)

10

(6 

(276 mm)

11

(6 

(302 mm)

41

556QE

(1059 mm)

22

6M

(578 mm)

FP2298
lorrider framing dims

gas 
Connection

FP2298

2 x 4 
Framing

10

(6 

(276 mm)

12

(314 mm)

41

556QE

(1059 mm)

23

56M

(591 mm)

FP2299
corner  framing dims

gas 
Connection

FP2299

2 x 4 Framing

Figure 11 - 
Framing Specifications for Peninsula 
Units (Model LPF36)

41

556QE

(1059 mm)

34

6M

(883 mm)

22

6M

(578 mm)

FP2300
penin framing

41

556QE

(1059 mm)

FP2300

Figure 12 - 
Framing Specifications for Corner Units 
(Model LRCF36/LLCF36)

41

556QE

(1059 mm)

23

56M

(591 mm)

34

6M

(883 mm)

FP2301
corner framing

FP2301

W

arnin

G

Do not fill spaces around firebox with 
insulation  or  other  materials. This 
could cause a fire.

note

All dimensions are based on 1/2" 
drywall. If 5/8" drywall is used, 
dimensions  must  be  changed 
accordingly.

Summary of Contents for LLCF36





















Reviews: