MHSC LLCF36 Installation And Operating Instructions Manual Download Page 18

18

79D0004

Lo-Rider Designer Vent Free Fireboxes

use of optional ak-4 outsiDe air kit

The use of outside air for combustion is optional unless required by building codes. It is 
only necessary to supply outside combustion air to one side of the fireplace. Use the model 
AK4 combustion air kit.

moDel ak-4 Combustion air assemblY

1.  Remove the cover plate from the 4" outlet opening location on the left or 

right outside of the fireplace. 

2.  Place  the  insulation  ring  between  the AK-4  starting  collar  and  fire-

place wall. 

3.  Place the starting collar (4") into the hole on the side of fireplace. Fasten 

it in place with the four sheet metal screws provided. 

Figures 26 and 28

note:  the air starting collar extends through the fireplace outer wrap. When the 
air starting collar is securely attached, it will form a seal against the fireplace wall.

4.  Attach outside duct to starting collar with duct clamp or screws. 

Figure 27

Do not remove the 
cover if the outside air 
will not be connected.

W

arnin

G

figure 26 - 
attaching outside air starting Collar and insulation 
ring to left side of fireplace 

figure 27 - 
attaching outside Duct to starting Collar

Insulation Ring

AK-4 Starting 
Collar 

Sheet Meal 
Screws 

left Side of 
Fireplace 

Shorter End of Air 
Starting Collar 

Air Starting 
Collar 

Duct 

Screws 

left Side of 
Fireplace 

5.  Cut a 6-inch diameter opening for model AK-4 in the out-

side wall covering where the outside vent is to be located. 

Figure 28.

6.  Select and cut a piece of duct long enough to attach to 

the fireplace and stick out at least 3" beyond the face of 
the wall to which the AK-4 inlet air vent will be attached. 

Figure 27

figure 28 - 
Combustion air assembly for model no. ak-4

Nail Holes 

use fp-4 u duct for maximum efficiency 
and safety. Do not use a combustible 
duct. always use ul listed Class 0 or 
1 duct material.

W

arnin

G

6" Diameter Hole 

Duct Extending
3"min. 

AK-4 Inlet Air 
Vent 

Screw

Screws

Summary of Contents for LLCF36





















Reviews: