Meyer EZ-Mount Plus Operation And Maintenance Manual Download Page 25

SNOW PLOWING OPEN AREAS

Open areas such as parking lots require a more serious approach 
to planning, where to begin, and where snow can be stacked at 
the edges.  The following will help in making a plan, thus turning 
out a neat, professional job.

Always  turn  on  warning  flashers  and/or  use  yellow  warning 
beacon or strobe light when plowing.  Then make a single pass 
down the center on the longest dimension.  Angle plow the snow 
toward the long sides with continuous passes until the area is 
cleared and snow is all stacked around the outside edges.

For  larger  areas,  efficient  plowing  calls  for  clearing  area 
immediately in front of buildings and working away from buildings 
toward the outer limits of the area.  When snow is quite deep, 
it might be necessary to push the excess into piles out of main 
traffic  lanes  for  later  handling.  Areas  100,000  sq.ft.  or  more 
— once the main artery is clear, it is usually most efficient to plow 
at right angles to the artery, piling up windrows by back and forth 
passes in alternate lanes.  The windrows can later be pushed out 
of the way or left as is depending upon conditions.

To clean up remaining snow, you can put the blade in the straight 
position.  Buck piles from either side to stack snow.  The blade 
will automatically “ride” up the pile to make stacking easier.

On a dirt or slag surface, drop moldboard to ground in straight 
position,  then  raise  one  inch  or  adjust  runners  for  desired 
clearance.  Under extreme surface conditions it may be necessary 
to plow with moldboard in suspended position.

PARKING LOTS

1. Always turn on warning flashers when plowing.
2. Make first pass to clear area into which you will later push 

more snow.

3. Clear  front  in  straight  position  and  clean  up  remaining 

snow.  Buck piles from either side to stack snow.  Blade will 
automatically “ride” up pile to aid in stacking.

4. Set the Super-V in the “V” or scooped position to clear between 

parked  cars  or  areas  where  it  is  necessary  to  make  short 
passes without snow spill over.

Snow Plowing Tips from the Pros

-23-

Summary of Contents for EZ-Mount Plus





































Reviews: