manualshive.com logo in svg

Metz Connect EWIO 2, User Manual

Share
Download
Metz Connect EWIO 2 User Manual Download Page 9

 

 

 

 

 

EWIO

2

 User Manual 

V 1.1 | Stand 10/2020 

 Seite 9 von 96 

 

 

METZ CONNECT GmbH | Im Tal 2 | 78176 Blumberg | Germany  
Tel. +49 7702 533-0 | Fax +49 7702 533-433 
For additional documentations look at www.metz-connect.com 

2.1.

 

Controller unit 

 

Prozessor NXP i.MX7D Dual Core  ARM

®

 Cortex

®

 - A7, frequency 1 GHz. 

Internal storage: 

 

- 512 MB RAM 

 

- 4 GB Flash. 

Operating system Linux embedded 

RealTimeClock: 

- with an accuracy of 1 s per day 

- 10 hrs. Power failure bridging 

 

2.2.

 

In- and outputs 

 
The EWIO

2

 and EWIO

2

-M variants are available: 

 

8 digital inputs for recording and counting binary states up to 24 Volt DC 

4 of them are galvanically isolated. 

 

4 switchable digital 24 Volt outputs with current carrying capacity of up to 20 mA DC 

per output 

 

3 analogue inputs. Configurable for  

- 0-10 Volt DC voltage measurement, 

- Resistance measurement in the range from 40 Ohm to 4 Megaohm or 

- Temperature measurement. 17 different sensor types can be selected. 

- 0-20mA DC current measurement, 

 

3 analog outputs with manual operation with 0-10 Volt DC with a 

current carrying capacity up to 5 mA per output. 

 
Only for EWIO

2

 variants are available: 

 

6 switchable relay outputs with manual operating up to 6 A per relay 

 

2 switchable TRIAC outputs with manual control with 20-250 Volt AC  

with a current carrying capacity of up to  0.5 A per TRIAC 

 

Only for EWIO

2

-M variants are available: 

 

4 switchable relay outputs with manual operating with one current carrying capacity  
up to 6 A per relay 

 

 

Summary of Contents for EWIO 2

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands