manualshive.com logo in svg

Metz Connect EWIO 2, User Manual

Share
Download
Metz Connect EWIO 2 User Manual Download Page 51

 

 

 

 

 

EWIO

2

 User Manual 

V 1.1 | Stand 10/2020 

 Seite 51 von 96 

 

 

METZ CONNECT GmbH | Im Tal 2 | 78176 Blumberg | Germany  
Tel. +49 7702 533-0 | Fax +49 7702 533-433 
For additional documentations look at www.metz-connect.com 

 

Press the blue bar to open and close the parameters for the "Automatic Backup". In the pop-

up menus, you can specify where, at what interval and how many backups are to be stored 

and how many are to be kept. If the interval is set to "Never", no automatic backup is 

performed. 
With the "Restore" function, you can select which data or configurations are to be uploaded 

to the device via the browser or from the SD card.

 

 

Clicking the action field "Choose a file" opens an explorer window to select the desired tar.bz2 

file. Only then the action field "Restore" can be activated. Here only the data can be restored 

that were saved before under the function "Save".  
Afterwards the device is restarted with the new settings. The hardware is not reset. 
In the login window it is indicated that a recovery of the data and configurations was the 

cause of the restart. 

Summary of Contents for EWIO 2

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands