Metz Connect EWIO 2 User Manual Download Page 14

Page: 14 / 96

EWIO

User Manual

V 1.1 | Stand 10/2020

Seite 14 von 96

METZ CONNECT GmbH | Im Tal 2 | 78176 Blumberg | Germany
Tel. +49 7702 533-0 | Fax +49 7702 533-433
For additional documentations look at www.metz-connect.com

Installation

4.1.

Installation location and state

The electrical installation and device connection may only be carried out by qualified

personnel in compliance with VDE regulations and local regulations.

Before working on the system, it must be disconnected from the power supply.

The EWIO

is intended for fixed installation and operation inside enclosed rooms in electrical

distribution boards and suitable control panels.

The EWIO

is designed for mounting on TH35 mounting rails in accordance with IEC 60715.

It can be installed in any position. Horizontal installation is recommended.

It is possible to add them to other control cabinet components without spacing.

4.2.

Elektronic block

In case of service the EWIO

may have to be replaced or the MicroSD card may have to be

removed in order to read out data saved on it.

In this case, the electronic block can be disconnected from the terminal module without

having to remove the connected cables.

The eject lever at the top right must be pushed back strongly. The electronic block can then

be easily removed.

Summary of Contents for EWIO 2

































































































Search results

Summary of Contents for EWIO 2

Reviews:

Brands by name

Popular brands

Metz Connect EWIO 2, User Manual

Search results

Summary of Contents for EWIO 2

Reviews:

Brands by name

Popular brands