Metronix BL 4104-C Mounting Instructions Download | Manualshive

Page: 18 / 36

background image

Page 18

Mechanical installation

Mounting Instructions „Servo drives BL 4000-C“

PRELIMINARY

Version 0.1

4

Mechanical installation

4.1

Important notes



Only use the servo drive BL 4000-C as a built-in device for switch cabinets



Mounting position vertical with supply lines [X9] on top



Mount to control cabinet plate using a fastening strap



Installation free spaces:

Keep a minimum distance of 100 mm to other components each above and underneath the device to
ensure sufficient venting.
For optimal wiring of the motor cable and angle encoder cable on the bottom of the device an
installation free space of 150mm is recommended!



Mounting distance:

The servo drive BL 4000-C may be installed adjacently in one switch cabinet without a gap, proper
usage and installation on a heat-dissipating rear panel provided. Please note that excessive heat may
cause premature aging and/or damaging of the device. In case the servo drives BL 4000-C are
subject to high thermal stress, a mounting distance of 59 mm is recommended!

«
...
16
17
18
19
20
...
»

Summary of Contents for BL 4104-C





































Reviews:

No comments

Related manuals for BL 4104-C

Brand: VEDER Pages: 13

Brand: Minarik Pages: 52

Brand: D+H Pages: 8

Brand: Fröling Pages: 44

Brand: Omron Pages: 48

Brand: YASKAWA Pages: 198

Brand: D+H Pages: 20

Brand: Becker Pages: 20

Brand: Becker Pages: 20

Brand: Becker Pages: 28

Brand: Becker Pages: 52

Brand: Berger Lahr Pages: 45

Brand: Robotis Pages: 21

Brand: Parker Pages: 321

Brand: Parker Pages: 347

Brand: Shur-Co Pages: 16

Brand: HAUTAU Pages: 8

Brand: Jenaer Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands