Metronix BL 4104-C Mounting Instructions Download | Manualshive

Page: 21 / 36

background image

Electrical installation

Page 21

Mounting Instructions „Servo drives BL 4000-C“

PRELIMINARY

Version 0.1

5

Electrical installation

INFORMATION

If they have the same DC bus voltage, it is possible to couple multiple servo drives of
the BL 4000-C series.

CAUTION!

If the DC buses are connected, the power supplies must be connected to the same
mains phase.
This means, if two BL 4000-C are coupled in the DC bus, only the connection L1/N is
possible for both devices. It is not allowed to connect the DC Busses if the devices are
connected to different mains phases.
It is forbidden to supply device 1 via L1/N and device 2 via L2/N, if the DC buses are
coupled.

CAUTION!

Operation with DC bus coupling together with devices of the ARS 2000 FS / SE series
is not allowed.

«
...
19
20
21
22
23
...
»

Summary of Contents for BL 4104-C





































Reviews:

No comments

Related manuals for BL 4104-C

PowerXL DM1 Series

Brand: Eaton Pages: 28

Brand: Eaton Pages: 5

Brand: Eaton Pages: 240

Brand: Eaton Pages: 34

Brand: Eaton Pages: 179

Brand: Eaton Pages: 46

PowerXL DG1 Series VFD

Brand: Eaton Pages: 24

PowerXL DG1 Series VFD

Brand: Eaton Pages: 152

Brand: Eaton Pages: 18

Brand: Eaton Pages: 58

Brand: Eaton Pages: 20

Brand: Eaton Pages: 195

Cutler-Hammer SLX9000 Series

Brand: Eaton Pages: 24

PowerXL DM1 Series

Brand: Eaton Pages: 68

MM G510.500 18 027

Brand: BAFANG Pages: 20

Brand: IBM Pages: 20

Brand: D+H Pages: 12

Sonesse ULTRA 30 WireFree RTS Li-ion

Brand: SOMFY Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands