Merida City Bikes Operating Instructions Manual Download Page 110

Page: 110 / 114

110

Bike card

Manufacturer

Model

Frame no.

Color

Drive system

Mid-mounted motor

Battery model

Key no.

Voltage (Volt)

Ampere-hour (AH)

Capacity (watt hours)

Suspension fork - Manufacturer

- Model

- Serial no.

Frame type

Frame size

Size of wheels and tires

Special features

Intended use

Category 0

Category 3

Category 1

Category 4

Category 2

Category 5

Permissible overall weight

MERIDA bike, rider and baggage

_________ kg

Pannier rack

yes

Permitted overall load

_________ kg

Child seat permitted

yes

Trailer permitted

yes

Permissible trailer load

_________ kg

Brake lever

Brake assignment

Right lever

Front wheel brake

Rear wheel brake

Left lever

Front wheel brake

Rear wheel brake

Read the chapter “Before your first ride” in the translation of

these original MERIDA operating instructions.

Stamp and signature of the MERIDA dealer

(Tip for the MERIDA dealer: Copy the bike card and the handover report and keep one copy in your customer file. Send another copy to the bike manufacturer)

Summary of Contents for City Bikes



















































































































Search results

Summary of Contents for City Bikes

Reviews:

Related manuals for City Bikes

Brands by name

Popular brands

Merida City Bikes, Operating Instructions Manual

Search results

Summary of Contents for City Bikes

Reviews:

Related manuals for City Bikes

Brands by name

Popular brands