Merida City Bikes Operating Instructions Manual Download Page 39 | Manualshive

Page: 39 / 114

background image

39

e

f

g

h

There are various types of brake systems that may be
subject to the following problems:

Rim brakes

(e)

are liable to overheating as a result of

too long braking or brake dragging. This can damage the
inner tube or make the tire slip on the rim, causing a
sudden loss of air which could lead to a serious accident
in the process.

With

roller, drum, back-pedal

and

disc brakes

(f+g)

prolonged braking or permanent dragging of brake pads
can also lead to an overheating of the brake system.
This can result in a reduction of the braking force or even
brake failure. Risk of an accident!

When riding downhill, get used to braking hard and then
releasing the brake again, whenever the road surface
and the situation allows for it. If you are in doubt about
the braking action, stop and let the brake system cool
down.

G

The assignment of brake lever to brake cal-

iper can vary, e.g. left lever acts on front

brake. Have a look at the bike card and check

whether the brake lever of the front brake is on the

side you are used to (right or left). If it is not, ask your

MERIDA dealer to switch the brake levers before you

set off for the first time.

G

Be careful while getting used to the brakes.

Practice emergency stops in a place clear of

traffic until you are comfortable controlling

your MERIDA bike. This can save you from having acci-

dents in road traffic.

G

Wet weather reduces the braking effect and

the road grip of the tires. Be aware of longer

stopping distances when riding in the rain, re-

duce your speed and actuate the brakes carefully.

G

Ensure that braking surfaces and brake pads

are absolutely free of wax, grease and oil.

Risk of an accident!

A

When replacing any parts, be sure to only

use parts that bear the appropriate mark and,

to be on the safe side, original spare parts

(h)

.

Your MERIDA dealer will be pleased to help you.

I

Be sure to read the instructions of the brake

manufacturers on this MERIDA CD-ROM

before you start to readjust or to service the

brake or before doing any work whatsoever.

«
...
37
38
39
40
41
...
»

Summary of Contents for City Bikes



















































































































Reviews:

No comments

Related manuals for City Bikes

Brand: Makita Pages: 16

Brand: Jetson Pages: 48

Brand: Hyena Pages: 13

Brand: TRIOBIKE Pages: 36

Brand: Shimano Steps Pages: 57

iAero Generation III

Brand: iBike Pages: 40

Brand: HP Velotechnik Pages: 6

Brand: Belize Bicycle Pages: 6

Brand: KZONE Pages: 14

Brand: wayscral Pages: 266

Brand: Yedoo Pages: 37

Brand: Cycle Torch Pages: 9

Brand: Marzocchi Pages: 29

Brand: USAC Pages: 12

Brand: Babyhug Pages: 2

Brand: hepco & becker Pages: 2

Brand: O2Feel Bikes Pages: 108

Brand: e-nova Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands