background image

104

Warranty and guarantee

Your MERIDA bike was manufactured with great care. Normally it is deliv-
ered to you by your MERIDA dealer fully assembled. 
As direct purchaser you have full warranty rights within the first two years 
after purchase. Please contact your MERIDA dealer in the event of defects. 
To ensure a smooth handling of your claim, it is necessary to present your 
receipt, your bike card and the handover report. Therefore, be sure to keep 
these documents in a safe place.
To ensure a long service life and good durability of your MERIDA bike, use 
it only for its intended purpose (see the chapters “Before your first ride“ and 
“Intended use”). Please observe the permissible load specifications as spec-
ified on the bike card. Be sure to follow the mounting instructions of the 
manufacturers (above all, the torque values of the bolts) as well as the pre-
scribed maintenance schedule. 
Observe the checks and routines listed in this translation of the original 
MERIDA operating instructions, in your comprehensive MERIDA user man-
ual, the system instructions of your drive manufacturer and the instructions 
of the component manufacturers on this MERIDA CD-ROM (see the chapter 
“Service and maintenance schedule” in your comprehensive MERIDA user 
manual) or the replacement of safety-relevant components, such as handle-
bars, brakes etc, if necessary.

Keep in mind that retrofitted accessories can impair the function-

ing of your MERIDA bike. If you are in doubt or if you have any 

questions, contact your MERIDA dealer.

The law referring to full warranty rights is only valid in the coun-

tries where the law has been ratified according to the renewed 

European regulations. Please inform yourself about the situation 

in your country.

incandescent bulbs/LED
rubber gribs
chainwheels
chainstay protection
lamps
tires
sprockets
saddle covering
pulleys
lubricants

rechargeable battery
drive chain
brake pads
brake fluid (DOT)
brake discs/rotors
brake cables
brake cable housings
seals of suspension elements
rim sides (of rim brakes)
rims (of rim brakes)

A note on wear

Some components of your MERIDA bike are subject to wear due to their 
function. The rate of wear will depend on care and maintenance and the 
way you use your MERIDA bike (mileage, riding in the rain, dirt, salt etc.). 
MERIDA bike that are often left standing in the open may also be subject to 
increased wear through weathering.

The components below require regular care and maintenance. Neverthe-
less, sooner or later they will reach the end of their service life, depending 
on conditions and intensity of use. Parts that have reached their limit of wear 
must be replaced:

Ask your MERIDA dealer about any additional guarantee given 

by the manufacturer of your MERIDA bike and insist on having it 

as printed version.

Summary of Contents for City Bikes



















































































































Reviews: