Memmert INCO 108 Operating Manual Download Page 61

Page: 61 / 64

Storage and Disposal

9. Storage and Disposal

9.1 Storage

The incubator may only be used under the following conditions.

Dry and in an enclosed, dust-free room

Frost-free

Disconnected from the power supply and gas supply

Undo gas bottle connections and close valves of gas bottles.

Gas bottles may be stored in closed rooms if these are sufficiently well ventilated.

For appliances with basic fittings:

Remove, empty and clean the water tray(s).

For appliances with the humidity module:

Undo hose connection of water supply tank; empty water tank.

9.2 Disposal

This product is subject to the Directive 2002/96/EC on Waste Electrical

Electronic Equipment (WEEE) of the European Parliament and of the EU

Council of Ministers. This appliance has been brought to the market

after 13th August 2005 in countries which have already integreated

this directive into their national laws. It may not be disposed of in

normal household waste. To dispose, please contact your dealer or

manufacturer. Any appliances that are infected, infectious or contami-

nated with materials that are a hazard to health are excluded from

being taken back. Please observe the other regulations in this context.
Before disposing of the appliance, please render the door locking

mechanism unusable, for example, to prevent playing children from

being locked inside the appliance.
Note for Germany:

The appliance may not be left at public or communal recycling or collection points.

Summary of Contents for INCO 108

































































Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands

Memmert INCO 108, Operating Manual

Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands