Memmert INCO 108 Operating Manual Download Page 18 | Manualshive

Page: 18 / 64

background image

18

Design and Function

2.11 Ambient conditions

Ź

The incubator may only be used in enclosed rooms and under the following environmental

conditions:

Ambient temperature: 5 ºC to 35 ºC

Humidity:

max. 80 % not condensing

Degree of pollution:

2

Altitude of installation max. 3,000 m above sea level

Ź

The incubator may not be used in areas where there is a risk of explosions. The ambient air

must not contain any explosive dusts, gases, vapours or gas-air mixtures. The incubator is

not explosion-proof.

Ź

Heavy dust production or aggressive vapours in the vicinity of the appliance could lead to

sedimentation in the chamber interior and as a consequence, could result in short circuits

or damage to electrical parts. For this reason, sufficient measures should be taken to

prevent large clouds of dust or aggressive vapours from developing.

2.12 Accessories included

For incubators with basic fittings:

g

Ź

Two (INCO 108) or three (INCO 153 and 246) sliding shelves

Ź

Gas pressure hose

Ź

Water tray (one for INCO 108 and 153 incubators, two for INCO 246 incubators)

Ź

Sterilisation chipcard

Additionally, for models with humidity module:

y,

y

Ź

Water supply tank and connection hose

Additionally, for models with CO

y,

22

or premium module:

p

Ź

Second gas pressure hose with quick-release connector

Additionally, for models with O

y,

22

module:

Ź

Second gas pressure hose with quick-release connector

«
...
16
17
18
19
20
...
»

Summary of Contents for INCO 108

































































Reviews:

No comments

Related manuals for INCO 108

Brand: Makita Pages: 64

Brand: Falltech Pages: 13

Brand: FALK Pages: 41

Brand: YOKOGAWA Pages: 12

GFS 10 - Fuel Sensor

Brand: Garmin Pages: 2

Brand: Xerox Pages: 2

Brand: Zhiyun Pages: 10

Brand: SIIG Pages: 12

Brand: B-Speech Pages: 24

Brand: turck Pages: 12

Brand: Thule Pages: 8

FDSB5481 Series

Brand: Viking Pages: 54

X5 Follow Focus

Brand: Camtree Hunt Pages: 4

Brand: Vega Pages: 92

Brand: Kargo Master Pages: 6

CombiCool CAB-40B

Brand: Waeco Pages: 136

Brand: CASTLECREEK Pages: 3

Brand: Inateck Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands