Memmert INCO 108 Operating Manual Download Page 33

Page: 33 / 64

Operation and control

5.10.4 Settings example week time switch

From Mo-Fr (workdays group), the appliance should switch on at 9.30 and switch off at

19.00. In addition it should work on Saturday from 10.00 to 14.00 ( Fig. 21 ).

9:30h - 19:00h

24:00h

12:00h

01:00h

9:30h - 19:00h

10:0h -

14:00h

Fig. 21

Operation with week time switch (example)

1. Setting the week time switch operating mode
Hold the SET key down for approx. 3 seconds, the current

operating mode then begins to flash. Select the week

time switch operating mode with the push-turn control,

while the SET key is held down.
Release the SET key, the control is now in the week time

switch operating mode.

SETUP

2. Switch on Mo-Fr at 09:30
Turning the push-turn control to the left, select the

Mo-Fr on

" icons (group working days).

Hold down the SET key and set the desired switch-on

time with the push-turn switch to

9:30

off

3. Switch off Mo-Fr at 19:00
Select "

Mo-Fr off

" (group working days) with the push-

turn control.
Hold down the SET key and set the desired switch-off

time with the push-turn switch to

19:00.

off

Summary of Contents for INCO 108

































































Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands

Memmert INCO 108, Operating Manual

Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands