Memmert INCO 108 Operating Manual Download Page 39

Page: 39 / 64

Warning messages and malfunctions

If humidity exceeds the

preset setpoint for longer

than 30 minutes.

Remedy: Open door for 30 sec.

and wait to see if the controller

steadily adjusts to the setpoint.

If the error occurs again, Contact

the customer service.

Error in CO

system:

if the CO

supply is defec-

tive

Remedy: Set CO

setpoint value

to 0, check stop valve of gas

bottle(s) and ensure that they

are properly connected; if gas

bottle(s) empty, change gas bot-

tles, set CO

setpoint to desired

value

If the CO

concentra-

tion exceeds the defined

setpoint by at least 1 % for

more than 3 minutes.

Remedy: Open door for 30 sec.

and wait to see if the controller

steadily adjusts to the setpoint.

If the error occurs again, Contact

the customer service.

Error in O

system:

off

e m p t y

supply is defective Remedy: check if the N

bottle

is correctly connected and if the

valve is open. If that does not

solve the problem, you should

connect a new gas bottle (see

page 23 ).

6.2 System/appliance errors

Warning!

After removing covers, live parts may be exposed. You may receive

an electric shock if you touch these parts. Malfunctions requiring in-

tervention inside the appliance may only be rectified by electricians.

You must read the separate service manual for the INCO incubator

for this.

Do not try and rectify the error yourself, but contact an authorised customer service point for

MEMMERT appliances or Contact the customer services department directly of the company

MEMMERT (see page 2 ).
In case of enquiries, please always specify the model and appliance number on the nameplate

(see page 15 ).

Summary of Contents for INCO 108

































































Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands

Memmert INCO 108, Operating Manual

Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands