Memmert INCO 108 Operating Manual Download Page 12

Page: 12 / 64

Design and Function

Digitalised electronic CO

control with automatic zero position, NDIR measuring system

with self-diagnosis system and acoustic error display, air pressure compensation

Language settings (see page 44 )

Alphanumeric text display

Integrated week time switch with grup function (e.g. each working day) (see page 31 )

Retracting push-turn control for simple operation of appliance (see page 26 )

Two separate Pt100 temperature sensors DIN Class A in a 4-wire circuit for control and

monitoring

Digital monitoring control for overtemperature, undertemperature and automatic

setpoint following (ASF) (see page 48 )

Mechanical temperature limiter (TB protection class 1, see page 45 )

Monitoring relay to switch off heater in case of error

Optical alarm display

Acoustic signal messages if temperature or CO

limits are crossed, when door is open and

if gas bottle is empty (see page 38 )

Calibration of temperature, humidity, CO

and O

possible on the device without a sepa-

rate PC (see from page 50 )

2.3.2 Optionally available additional modules

Comfort module:

Two gas connections with quick release connectors (see page 13)

Automatic switch-over of gas bottles

Hygiene module

Electro-polished, seamless laser-welded chamber

Communication module

Logging option of temperature, CO2 and relative humidity via computer/laptop

Internal log memory with 1024 kB as ring memory for all setpoint and actual values, errors

and settings in real time and with date, logging approx. 3 months at 1 minute storage

interval (see page 58 )

Parallel printer port (PCL3-compatible) for printing out log data (see page 13 and page 43 )

optionally USB, Ethernet, RS-232 or RS-485 interface (see from page 55 )

module

Extended adjustment range from 0 to 20 %

3-point calibration (5 %, 10 %, 15 % CO

)

module

Control of oxygen concentration through the introduction of nitrogen (N

); adjustment

range 1 % to 20 % O

(not in combination with Comfort or Premium module)

Premium module

Includes comfort, hygiene, communication and CO

modules

Humidity module

Active microprocessor humidification and dehumidification control (40-97 % rh)

Summary of Contents for INCO 108

































































Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands

Memmert INCO 108, Operating Manual

Search results

Summary of Contents for INCO 108

Reviews:

Related manuals for INCO 108

Brands by name

Popular brands