Meltem 710000 Installation Manual Download Page 33

Page: 33 / 44

- 33 -

Installation manual

M-WRG-II M

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

9.9

Inserting flat ductwork into ductwork connection adapter (only when

connecting a flat ductwork system)

NOTICE

If you are using flexible pipes, continue from section “9.10 Joining flexible pipe connec

tors and cutting flexible pipes to length (only when connecting a flexible pipe system)”

on page 34.

►

Loosen the two cross-head screws

(item 1 in Fig. 28) and lift up the bar

catch (item 2 in Fig. 28).

► Remove the flat ductwork bend

(item 3 in Fig. 28) from the ductwork

connection adapter (item 4 in

Fig. 28).

► Insert a flat duct M-WRG-FK-F

(item 5 in Fig. 28), part no. 5590, or

the fitting adapter M-WRG-FSA lang,

part no. 5375-00, into the flat

ductwork bend.

►

Seal the join with a layer of sealing

tape 30 mm wide (item 6 in Fig. 28).

► Push the flat ductwork bend (item 3

in Fig. 28) together with the attached

flat ductwork element (item 5 in Fig. 28) back into the ductwork connection adapter

(item 4 in Fig. 28).

► Push the bar catch (item 2 in Fig. 28) down and carefully tighten the cross-head

screws (item 1 in Fig. 28).

► Join individual elements of the flat ductwork to create partial sections and seal every

join with a layer of sealing tape 30 mm wide.

► Insert the sections of flat ductwork one after another and seal every join with a layer of

sealing tape 30 mm wide.

► Fix the flat ductwork in place with expanding foam or perforated tape.

Fig. 28:

Inserting flat ductwork into ductwork

connection adapter

Summary of Contents for 710000













































Search results

Summary of Contents for 710000

Reviews:

Related manuals for 710000

Brands by name

Popular brands

Meltem 710000, Installation Manual

Search results

Summary of Contents for 710000

Reviews:

Related manuals for 710000

Brands by name

Popular brands