manualshive.com logo in svg

Meltem 710000, Installation Manual

"Meltem 710000 Installation Manual: Easily set up the Meltem 710000 with our comprehensive manual. Available for free download at manualshive.com, our user-friendly manual provides step-by-step instructions, ensuring a hassle-free installation process. Get started today and unlock the full potential of your Meltem 710000."

Share
Download
background image

- 19 -

Installation manual 

M-WRG-II M

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION  THE  RIGHT WAY

V E N T I L A T I O N   &   H E A T   R E C O V E R Y

7 

Tools and equipment required

 

— Permanently elastic sealant, solvent-free if applied to polystyrene

 

— Sealing tape, 30 mm wide, e.g. Coroplast

 

— Sealing tape for bonding the wall box to the vapour barrier, e.g. Rissan

®

 from SIGA

 

—

If necessary, wedges for fixing the wall box, 8x 

 

alternatively use inflatable air cushions, 4x, e.g. Amo-Bag from Würth, 

part no. 07156780

 

—

If necessary, wedges for fixing the filler piece, 4x 

 

alternatively use inflatable air cushions, 2x, e.g. Amo-Bag from Würth, 

part no. 07156780

 

— Adhesive tape

 

—

Perforated tape for fixing flat ductwork or flexible pipes

 

—

Expanding foam with abP (national technical test certificate of the DIBt) approval 

(“exact gap” foam is recommended)

 

— Saw for cutting the ventilation pipes to length

 

— Saw for cutting the channels in the frame construction

 

— Styrofoam saw

 

— Spirit level

8 

General installation instructions

NOTICE

 

— The unit must be installed in accordance with the generally acknowledged rules of 

technology.

 

— Connections with adjacent components must be formed to absorb movements 

between the contact surfaces.

 

—

Seal any connections that are exposed to driving rain with tapes, profiles or sealants 

such that they offer sufficient protection against the expected conditions.

 WARNING

Follow the relevant accident prevention regulations

 

►

Follow the accident prevention regulations when setting up the installation location.

 

►

Protect the outside area against falling parts.

Summary of Contents for 710000













































Reviews:

No comments

Related manuals for 710000

Fanimation Bourbon Street FP510 Series Specification Sheet preview
Bourbon Street FP510 Series
Brand: Fanimation Pages: 2
Fanimation Americana FP410 Series Specification Sheet preview
Americana FP410 Series
Brand: Fanimation Pages: 2
Fanaway Montclair Installation Instructions Manual preview
Montclair
Brand: Fanaway Pages: 22
Fanaway LED EVO1 Installation, Operation, Maintenance And Warranty Information preview
LED EVO1
Brand: Fanaway Pages: 11
Fanaway EVO2 Installation Instructions Manual preview
EVO2
Brand: Fanaway Pages: 9
Fanaway EVO1 - PREVAIL Installation Instructions Manual preview
EVO1 - PREVAIL
Brand: Fanaway Pages: 6
Fanaway VEIL Manual preview
VEIL
Brand: Fanaway Pages: 36
Fan-Tastic Vent 7350 Operation Manual preview
7350
Brand: Fan-Tastic Vent Pages: 8
Xpelair GX6 EC3 RF Installation And Maintenance Instructions Manual preview
GX6 EC3 RF
Brand: Xpelair Pages: 12
AIGOSTAR 330100JTR Instruction Manual preview
330100JTR
Brand: AIGOSTAR Pages: 26
Trox Technik BVRA Installation And Operating Manual preview
BVRA
Brand: Trox Technik Pages: 64
AAF AstroFan EC FFU Installation, Operation And Maintenance Manual preview
AstroFan EC FFU
Brand: AAF Pages: 18
ebm-papst A2D250-AI14-10 Operating Instructions Manual preview
A2D250-AI14-10
Brand: ebm-papst Pages: 10
Martec Avoca DC Series Installation Manual preview
Avoca DC Series
Brand: Martec Pages: 4
NuAire HPKF Installation And Maintenance preview
HPKF
Brand: NuAire Pages: 4
ebm-papst D3G146-HQ13-34 Operating Instructions Manual preview
D3G146-HQ13-34
Brand: ebm-papst Pages: 11
SystemAir Fantech HERO 200H Installation And Operation Manual preview
Fantech HERO 200H
Brand: SystemAir Pages: 32
S&P Decor-100 CHZ Visual Manual preview
Decor-100 CHZ Visual
Brand: S&P Pages: 54

Brands by name

Popular brands

Load more brands