Mellanox Technologies Grid Director 4700 Installation Manual Download Page 78

Page: 78 / 88

System Cabling

9.1.1

Installing Cabling Guide Brackets

Left and Right brackets are marked "L" for left and "R" for right. When installed, make sure
that the grips face out.

The rack-gripping brackets shown, are installed on the 4700 rack’s rear rail.



To install the rack-gripping cabling guide brackets:

Install the cabling guide brackets at the rear of the rack itself, on the rail, and not on the
4700 chassis. It is not important from the cable management perspective where on the rack
the 4700 is installed.

Install the cabling guide brackets in parallel with the 4700 chassis so that each Line Board
lines up with its corresponding hanger on the bracket.

Summary of Contents for Grid Director 4700

























































































Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands

Mellanox Technologies Grid Director 4700, Installation Manual

Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands