Mellanox Technologies Grid Director 4700 Installation Manual Download Page 19

Page: 19 / 88

Mellanox Grid Director 4700 Installation Manual



Cable management (standard)



Rail kit



19" bracket attached to the chassis



KIT-00022 includes 3 parts (must be purchased separately for the 648-port
configuration):



1 HyperScale cabling guide bracket



2x bracket long



8 screws

2.1.2

Specifications Summary

The following table summarizes the Grid Director 4700 specifications.

Table 2: Feature Summary Table

Feature

4700

Rack Height

19U

HyperScale Rack Height

20U

Rack Width

19"

Switch Type

Director

Backplane Bandwidth

51.8 Tbps

Line Board Slots

Fabric Board Slots

Max # of InfiniBand Ports

324 40 Gbps InfiniBand Ports

Optional 648 40 Gbps InfiniBand Ports

Interface Type

QSFP 40 Gbps (QDR) QSFP ports with support for optical
adapters and cables

Redundant Components

Power Supplies (sPSU-S)

Management Boards (sMB-CM)

Embedded Chassis Management (CLI)

Yes

2.2

4700 Configuration and Part Numbers

The following table details the basic configuration of the 4700 chassis.

Table 3: 4700 Basic Configuration

Product Description

Product/Module
Name

P/N

Grid Director 4700 18-Slot QDR Basic Configuration

Grid Director 4700

VLT-30040

sFB-4700 QDR Fabric Board

sFB-4700

VLT-30041

sFB-4700-2X QDR Fabric Board

sFB-4700-2X

VLT-30042

Summary of Contents for Grid Director 4700

























































































Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands

Mellanox Technologies Grid Director 4700, Installation Manual

Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands