Mellanox Technologies Grid Director 4700 Installation Manual Download Page 39 | Manualshive

Page: 39 / 88

background image

Mellanox Grid Director 4700 Installation Manual

39

Mellanox PN

Description

Frequency

Card

OSC-00009

OSCILLATOR, 2.5V HCMOS/TTL
66.66MHZ 50 PPM

66.66MHz

sFB-4700, sFB-4700-2X,
sLB-4018, sMB-CM

141C65000

OSCILLATOR 50MHZ 7.5 X 5.0 X
1.4 MM 3.3V +50PPM

50MHz

sFB-4700, sFB-4700-2X,
sLB-4018

OSC-00008

OSCILLATOR 3.3V CMOS 48MHZ
50 PPM

48MHz

sMB-CM

OSC-00007

OSCILLATOR HCMOS/TTL
25MHZ

25MHz

sMB-CM

OSC-00011

OSCILLATOR HCMOS/TTL
25MHZ 2.5V

25MHz

sFB-4700, sFB-4700-2X,
sLB-4018

OSC-00010

OSC. HCMOS/TTL 25MHZ 1.8V
50PPM TR=4NS MAX 7X5MM

25MHz

sMB-CM

OSC-00006

OSCILLATOR SE 1.8V 19.2MHZ
+-50PPM

19.2MHz

sMB-CM

3.25

Shock and Vibration Test Reports

Prepare the Grid Director 4700 to ship in a rack by carefully following the rail kit installation
instructions, as detailed in Assembling and Mounting the Rails. The Grid Director 4700 is
susceptible to shock and vibration if the rail kit installation instructions are not followed
precisely.

The following tables detail the shock and vibration test reports, compliant with shipping in a
rack.

3.25.1

4700 Test for Transportation without a Rack

Table 27: Vibration

Test

Description

Vibration Axes

3 axes (X,Y,Z)

Non-Operating Random
Vibration

Frequency range:

5–300Hz

Vibration level:

Z axis, 1.03g RMS

X,Y axis 0.698g RMS

Vibration test for each axis

60 minutes

Operating Sine
Vibration

Frequency range:

5-500Hz

Vibration level:

0.1G peak

Vibration test for each axis

40 minutes

Operating Shock
(half-sine)

Vibration Level

Z axis, 5g peak

Shock test for Z axis

3 shocks, 10ms duration each shock

«
...
37
38
39
40
41
...
»

Summary of Contents for Grid Director 4700

























































































Reviews:

No comments

Related manuals for Grid Director 4700

OfficeConnect 5

Brand: 3Com Pages: 2

OfficeConnect 3C1670500C

Brand: 3Com Pages: 18

Instant On 1930 24G 4SFP/SFP+l

Brand: Aruba Pages: 48

Brand: LONG-JOIN Pages: 2

24-Port Gigabit Switch

Brand: Belkin Pages: 2

PerfectView GPS300

Brand: Waeco Pages: 72

AMX ENOVA DVX-3250HD-SP

Brand: Harman Pages: 119

Brand: Omron Pages: 4

Brand: Cable Electronics Pages: 12

Signal Distribution Box SDB45

Brand: Audiovox Pages: 12

Brand: I-Tech Pages: 22

AVS-OP-1616-567SD

Brand: AMX Pages: 1

Brand: ALFAtron Pages: 32

Brand: Intelix Pages: 40

Brand: Maretron Pages: 9

Brand: Manhattan Pages: 2

920-9B210-00FN-0D0

Brand: Nvidia Pages: 59

Spectrum 2E42-27

Brand: Cabletron Systems Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands