T. 1300 222 445 | www.melec.com.au
For further information about our Warranties please go to:
melec.com.au/legal/warranties
TECHNICAL INFORMATION
Zigbee to DALI+0/1-10V 2 in 1 Converter
Function introduction
Important:
Read All Instructions Prior to Installation
Product Data
•
•
•
Safety & Warnings
•
•
•
•
•
•
•
•
•
•
•
•
•
•
under DALI mode
•
•
•
•
•
•
•
•
Operation
1) Select
DALI or 0/1-10V Output Using
Switch 10
Note:
3) Select DALI Address or Group Control Mode Using D Switch 7
Note:
4)
Note: here device type is selected as DIM as an example, please select your correct DALI device type.
Select the DALI Group to be Controlled Using D Switches 2-6
Note: 1)
DIP
2)
3)
up
℃
℃
Note:
2) Select DALI Device Type (DT6/DT8 Color Type) to be Controlled Using DIP Switches 8-9
DA/-
L
L1
DA/+
Prog.
N
N
ML-ZIG-010D
ZigBee to DALI+0/1-10V
2 in 1 Converter with Relay
110-240V ~ 50/60Hz
Max. load: 5A Resistive
1E4
DALI
0/1-10V
DALI Add.
μ
•tc=75°C
20T 50
1.6A LED
• Zigbee to DALI+0/1-10V 2 in 1 converter based on Zigbee 3.0
•
Zigbee signal inpit 110-240VAC power input, DALI signal output ro DALI line or 0/10V signal output
• Max. 5A relay and metering function
•
Compatible with universal Zigbee gateway or hub products
•
Can directly pair to a compatible Zigbee remote via Touchlink
•
Compatible with universal Zigbee remotes
• Supports self-forming Zigbee network without coordinator
• Supports find and bind mode to bind a Zigbee remote
• Supports Zigbee green power and can bind max. 20 Zigbee green power remotes
• DALI signal or 0/1-10V signal output selectable by DIP switches
• Built-in DALI bus power supply, no extra DALI bux PS required
• With max. 50mA DALI bus power current output
• Able to supply control current up to 25 DALI control devices
• DALI DT6 or DT8 device type selectable by DIP switch under DALI mode
•
Color control according to DALI specifications of Device Type 8
•
Color type: Tc, XY coordinates, RGBW selectable by DIP switches
• DALI address control mode or group control mode selectable by DIP switch
• DALI address (00-63) to be controlled by DIP switches
• DALI group (0-15) to be controlled by DIP switches
•
Control 1 DALI Group of devices or 1 DALI address on DALI line
•
Control all devices on DALI via broadcast
SAFETY & WARNINGS
• DO NOT set the DIP switches with power applied to the device.
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
• The product shall be installed and serviced by a licensed electrician
• IP20. Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water-proof enclosure
• Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
• Please check if the output voltage of any LED power supplies used complies with the working voltage of the product.
• Never connect any cables while power is on always assure correct connections to avoid short circuit before switching on.
• Please ensure that the cable is secured tightly to the connector.
• Follow all relevant electrical and safety standardS (AS3000).
• All components must not be mechanically stressed
• Be careful not to damage or destroy conductive paths on the circuit board
•
Correct electrical polarity must be observed as the wrong polarity may destroy the product and is not covered under warranty
• Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against
corrosive agents such as moisture, condensation and other harmful elements
