T. 1300 222 445 | www.melec.com.au
For further information about our Warranties please go to:
melec.com.au/legal/warranties
TECHNICAL INFORMATION
5) Select the DALI Address to be Controlled Using Switches 1-6
Note: here device type is selected as DIM as an example, please select your correct DALI device type.
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9 10
9 10
Controlled address
Controlled address
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Note: 1)
once DALI device type and address control mode are selected, please then select the DALI address
2)
.
(00-63 selectable) to be controlled on DALI line by dial switches.
The control gear with the selected DALI address on DALI line will be controlled
1 2 3 4 5 6 7 8 9 10
Switch up
Switch down
6. ZigBee Clusters the device supports are as follows:
Input Clusters
•
0x0000: Basic
•
0x0003: Identify
•
0x0004: Groups
•
0x0005: Scenes
•
0x0006: On/off
•
0x0008: Level Control
•
0x0300: Color Control
•
0x0b05: Diagnostics
Output Clusters
•
0x0019: OTA
7. Do wiring according to connection diagram correctly.
8. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
9. Zigbee Network Pairing through Coordinator or Hub
(
Added
to
a
Zigbee
Network
)
10. TouchLink
to
a
Zigbee
Remote
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) To control through both gateway and remote, add remote and device to gateway network first
then TouchLink
4) After TouchLink, the device can be controlled by the linked remotes.
Step 1
: Remove the device from previous zigbee network if it has already been added to
,
otherwise
pairing
will
fail
.
Please
refer
to
the
part
"
Factory
Reset Manually
".
Step 2
: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 4
: LED indicator will blink 5 times
and then stay solid on, then the device
will appear in your controller's menu
and can be controlled through
controller or hub interface.
Step 1: Method 1
: Short press “Prog” button 4 times (or reset power of the device 4 times from master breaker) to
start Touchlink commissioning (lasts for 180S) immediately under any circumstances, once time out, repeat this
step.
Method 2
: Reset power of the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee
network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout.
Once timeout, repeat
the step.
Step 3
: Reset power of the device from master circuit breaker to set it into network pairing mode (connected
light flashes twice slowly), network pairing mode lasts 15S (enters into touchlink mode after 15S), once
timeout, repeat this step.
Step 4
: There shall be indication on
the remote for successful link and LED
indicator on the device will flash twice.
Zigbee
Remote
Step 2
: Bring the remote or touch panel within 10cm of the lighting device
.
Step 3
: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch panel manual to learn how
.
< 1
0c
m
L N
DALI Add.
1
5
3
7 9
2
6
4
8 10
L
L1
N
N
DA/-
DA/+
Prog.
DALI
0/1-10V
Input Voltage: 110-240V AC
Output Current: 1x5A max
ZigBee to DALI+0/1-10V
2 in 1 Converter with Relay
ta:-20
℃
-+50
℃
L N
DALI Add.
1
5
3
7 9
2
6
4
8 10
L
L1
N
N
DA/-
DA/+
Prog.
DALI
0/1-10V
Input Voltage: 110-240V AC
Output Current: 1x5A max
ZigBee to DALI+0/1-10V
2 in 1 Converter with Relay
ta:-20
℃
-+50
℃
WIRING DIAGRAM WHEN 0/1-10V OUTPUT SELECTED
Zigbee Lighting Device
Step 2
: Set another device, remote or touch panel into network pairing mode and pair to the network, refer to their
manuals
.
Step 3
: Pair more devices and remotes to the network as needed, refer to their manuals.
Step 4
: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the
remotes, refer to their manuals.
Note: 1) Each added device can link and be controlled by max. 30 added remotes.
2) Each added remote can link and control max. 30 added devices.
18. OTA
The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or
hub every 10 minutes automatically.
17. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)
Step 1
: Short press “Prog.” button 4 times (Or reset power to the device 4 times) to enable the device to form a zigbee
network (LED indicator flashes twice) to discover and add other devices, 180 seconds timeout, repeat the step.
Zigbee
Remote
< 10cm TouchLink
0/1-10V Dimmable
Driver
ACL
ACN
DIM+
DIM-
LED+
Wiring Diagram
When 0/1-10V Output Selected
L N
Max
. 5
A Rela
y
LED+ V+
LED light
9
7
3 5
1
0
1
8
4 6
2
LED-
LED- V-
When DALI Output Selected
Note
: 1) Max. 50mA DALI bus PS output to supply control current to up to 25 control devices.
2) The max. load of the relay is 5A, and the number of control gear can be switched by the relay
depending on the load of each control device.
L N
Max
. 5
A Rela
y
DALI Bus
DA
DA
DALI DT6/DT8 Control Gear
L
N
DA
DA
DALI DT6/DT8 Control Gear
L
N
LED+
LED-
LED+
LED-
LED+ V+
LED- V-
LED+ V+
LED- V-
LED light
LED light
DALI Add.
9
7
3 5
1
0
1
8
4 6
2
L N
DALI Add.
9
7
3 5
1
0
1
8
4 6
2
DA/-
L
L1
DA/+
Prog.
N
N
ML-ZIG-010D
ZigBee to DALI+0/1-10V
2 in 1 Converter with Relay
110-240V ~ 50/60Hz
Max. load: 5A Resistive
1E4
DALI
0/1-10V
DALI Add.
μ
20T 50
1.6A LED
DA/-
L
L1
DA/+
Prog.
N
N
ML-ZIG-010D
ZigBee to DALI+0/1-10V
2 in 1 Converter with Relay
110-240V ~ 50/60Hz
Max. load: 5A Resistive
1E4
DALI
0/1-10V
μ
20T 50
1.6A LED
DA/-
L
L1
DA/+
Prog.
N
N
ML-ZIG-010D
ZigBee to DALI+0/1-10V
2 in 1 Converter with Relay
110-240V ~ 50/60Hz
Max. load: 5A Resistive
1E4
DALI
0/1-10V
μ
20T 50
1.6A LED
