background image

 

 

 

since fabr. no. 94 12 5000 

 

subject to technical alterations 

 
 

Operation Manual

 

 

Quick autoclave 

 

MELA

quick

®

12

 

 
 

 
 

Dear Doctor: 

Thank you very much for the trust which you have shown by purchasing this autoclave. 

For 50 years now, MELAG — a medium-sized family-owned and -operated business — 
has specialized in the production of sterilization equipment for medical practice.  During 
this period, MELAG has succeeded in becoming a leading manufacturer of sterilization 
equipment.  More than 335.000 MELAG units sold throughout the world testify to the ex-
ceptional quality of our products — which are manufactured exclusively in Germany. 

As all other MELAG products, this autoclave was manufactured and tested according to 
strict quality criteria.  Before placing this unit into operation, please thoroughly read this 
Operating Manual.  The long-term functional effectiveness and the preservation of the 
value of your autoclave will primarily depend on careful preparation of instruments before 
sterilization, and on proper care of the unit. 

The management and staff of MELAG 

 

 

 

Summary of Contents for MELAquick 12




























Reviews: