Meinberg IMS LANTIME M500 Manual Download

Page: 101 / 132

12 Attachment: Technical Information

12.6.15 TSU V3: IEEE-1588 Time Stamp Unit

TSU v3 (IEEE 1588 v2 compatible)

Profiles:

IEEE 1588v2 Default Profile
IEEE C.37.238 Power Profile
ITU-T G.8265.1 Telecom Frequency Profile
ITU-T G.8275.1 Telecom Phase/Time Profile
SMPTE ST 2059-2 Broadcast Profile

PTP Modes:

Multicast Layer 2 (IEEE 802.3)
Multicast/Unicast Layer 3 (UDP IPv4/IPv6)
E2E / P2P Delay Mechanism
Bis 128 messages/second per client

NTP Mode:

NTP Server mode (10 ns time stamp accuracy)

1588 Clock Mode:

1-Step, 2-Step for both Master and Slave operation

Synchronous Ethernet:

Master and Slave Capability
Compliant to ITU-T G.8261, G.8262 and G.8264
Ethernet Synchronization Messaging Channel (ESMC)

Network Protocols:

IPv4, IPv6
DHCP, DHCPv6
DSCP
IEEE 802.1q VLAN filtering/tagging

Ethernet Interface:

Combo Port:
1 x 100/1000BASE-T RJ45
1 x GBIT SFP - Slot

Signal Outputs:

2x BNC (50 Ohm) connectors
configurable signals: 1PPS, 10MHz, 2048kHz

CPU:

1 GHz Dual Core ARM

Time Stamp Accuracy:

10 ns

IMS - LANTIME M500

Date: 19th March 2020

Summary of Contents for IMS LANTIME M500





































































































































Search results

Summary of Contents for IMS LANTIME M500

Reviews:

Related manuals for IMS LANTIME M500

Brands by name

Popular brands

Meinberg IMS LANTIME M500, Manual

Search results

Summary of Contents for IMS LANTIME M500

Reviews:

Related manuals for IMS LANTIME M500

Brands by name

Popular brands