Meinberg IMS LANTIME M500 Manual Download

Page: 66 / 132

Status Indicators

LED St:

MRI status

LED In:

Status of the backplane’s reference signals

LED A:

Status of the input signals (TC-AM/DCLS) at the board

LED B:

Status of the input signals (10 MHz/PPS) at the board

Initialisation:

LED St: blue until USB is configured
LED In - LED B: off until USB is configured

USB is configured:

LED St: blue
LED In - LED B:
0,5 sec. red -> 0,5 sec. yellow -> 0,5 sec. green -> 0,5 sec. off

Normal Operation:

LED St + LED In: green
LED A: green, if timecode AM or timecode DCLS
or both signals are available at the same time
LED B: green, if 10 MHz or PPS
or both signals are available at the same time

Power Requirements:

5 V +-5%, 50 mA

Date: 19th March 2020

IMS - LANTIME M500

Summary of Contents for IMS LANTIME M500





































































































































Search results

Summary of Contents for IMS LANTIME M500

Reviews:

Related manuals for IMS LANTIME M500

Brands by name

Popular brands

Meinberg IMS LANTIME M500, Manual

Search results

Summary of Contents for IMS LANTIME M500

Reviews:

Related manuals for IMS LANTIME M500

Brands by name

Popular brands