Meinberg IMS LANTIME M500 Manual Download Page 38

Page: 38 / 132

When pressing "F1" from main menu a short description for menu navigation will be displayed:

Use -> and <- to
select different
main menus. Use
^ and v to enter

When pressing the "OK" button from main menu the version of the LANTIME software, the NTP and the LINUX
kernel version will be displayed.

E900 V7.0
SN : 0608120010
CPU : 0047115827
Bld.: 7.00.006

The following main menus will be displayed when pressing the "

↑

" and "

↓

" arrow buttons:

E900 V7.0
SN : 0608120010
CPU : 0047115827
Bld.: 7.00.006

->Ref. Time
Time Service
Network
System

-> Setup MRS
Info GPS
Setup GPS
Set Outputs

Ref. Time
->Time Service
Network
System

-> NTP Settings<-
PTP IEEE1588

Ref. Time
Time Service
->Network
System

-> Interfaces <
Global Cfg.
Services
Add Interf.

Ref. Time
Time Service
Network
->System

> Time Zone
Options
System Info
Fan Control

Date: 19th March 2020

IMS - LANTIME M500

Summary of Contents for IMS LANTIME M500





































































































































Search results

Summary of Contents for IMS LANTIME M500

Reviews:

Brands by name

Popular brands

Meinberg IMS LANTIME M500, Manual

Search results

Summary of Contents for IMS LANTIME M500

Reviews:

Brands by name

Popular brands