Megger SMART THUMP ST16 User Manual Download Page 9 | Manualshive

Page: 9 / 62

background image

AVTMST16 Rev 1 May 2016

iii

Receiving Instructions

1.

Check the equipment received against the packing list to ensure that all materials are
present. Notify Megger of any shortage. Email your local Service Representative or
send to

[email protected]

.

2.

Examine the equipment for damage received in transit. If damage is discovered, file a
claim with the carrier at once and notify Megger, giving a detailed description of the
damage.

3.

Prior to operation, check for loosened hardware or damage incurred during transit.
If these conditions are found, a safety hazard is likely, DO NOT attempt to operate
equipment.

Please contact Megger as soon as possible.

Please check your delivery against:

a) your order
b) our advice note
c) the item delivered, and
d) the parts list

any shortages must be reported immediately.

Consultation with Megger

The present system manual has been designed as an operating guide and for
reference. It is meant to answer your questions and solve your problems in as
fast and easy a way as possible. Please start with referring to this manual should
any trouble occur.

In doing so, make use of the table of contents and read the relevant paragraph
with great attention. Furthermore, check all terminals and connections of the
instruments involved.

Should any question remain unanswered, please contact:

[email protected]

or

phone: +1.610.676.8500 (USA)

«
...
7
8
9
10
11
...
»

Summary of Contents for SMART THUMP ST16































































Reviews:

No comments

Related manuals for SMART THUMP ST16

FX-ARM CONTROLLER

Brand: Magicfx Pages: 16

Brand: JB Systems Pages: 7

Brand: 3B SCIENTIFIC PHYSICS Pages: 36

Brand: 3A HEALTH CARE Pages: 16

Short/cut 2000 Audio Editor

Brand: 360 Systems Pages: 4

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Brand: Fellowes Pages: 20

Optima XR200amx

Brand: GE Pages: 46

Brand: GE Pages: 241

Brand: GE Pages: 223

Brand: Lencarta Pages: 6

Brand: Marani Pages: 35

Serious Steel 805106

Brand: ParaBody Pages: 6

Z33-D060.02 S2A

Brand: Jäger Pages: 36

Royal Squat Rack SX-5 II

Brand: KingsBox Pages: 5

Brand: TOPMAQ Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands