manualshive.com logo in svg

Megaplot XMD Series, User Manual, Page: 73 / 73

Share
Download
Megaplot XMD Series User Manual Download Page 73

 page 73 of 73

MAINTENANCE RECOMMENDATIONS 

MAINTENANCE RECOMMENDATIONS 

Always observe all applicable safety laws.

Keep the ball screws and linear guides clean. Dust them off and grease on a regular basis.

Keep the proximity sensors and screw covers clear. Dirty screw covers may prevent the machine 

from homing properly as the portal may be blocked before it reaches the proximity sensors.

Keep the machine clean of any material chips. It is recommend it to clean the machine off with 

compressed   air   on   regular   basis.   Do   not   use   a   vacuum   during   the   router's   operation   as   the 
electrostatics may interrupt machine operation. 

Use   distilled   water   for   the   water   cooling   system.   The   water   pump   should   be   completely 

underwater at all times. Make sure none of the pipes feeding the water are bent or damaged. 

To avoid overloading the spindle, always use tools suitable for given material. Set the important 

parameters   such   as   speed,   rotations,   width   and   depth   of   passes   bearing   in   mind   the   material 
properties and the used tool.

www.megaplot.com

 phone: +48 693 707 575  

[email protected]

Summary of Contents for XMD Series










































































Reviews:

No comments