Megaimpulse NRG1001 User Manual Download Page 3

Page: 3 / 16

CONTENTS

Safety manual ................................................................................................... 2

Description and general view of the generator ................................................. 3

Technical specification ..................................................................................... 5

Front and rear panels view ................................................................................ 6

Package content ................................................................................................ 7

Putting the generator into operation .................................................................. 8

Triggering of the generator ............................................................................... 11

SYNC OUT pulse ............................................................................................. 12

Fuse replacement .............................................................................................. 13

Warranty ........................................................................................................... 14

User manual of NRG1001 HV rectangular pulse generator 1

Summary of Contents for NRG1001
















