MCM Electronics iRIS8+ Installer Manual Download Page 32

Page: 32 / 32

Page 32

iRIS 8 Enhancement and versions

IRIS8 Software Version
V7.82

Added Option 4 in Function 87 – Enable GSM Fail Reporting, Single flash of FIRE

led equals GSM fail

Added Option 8 in Function 80 – Enable GSM Fail Output

Added Option 4 in Function 93 – Momentary Arm only for Full & Part Key switches

Added Chime On/Off – Hold down 4 key to toggle chime on/off.

2 beeps for On / 3 beeps for Off

Fixed Line Fail & Tamper report order when both event & restore are pending

Increased inter-digit timeout from 3 sec to 5 sec when using User, Master or Tech codes

Changed Cancel by User CID code to event not restore

V7.71
-

Added “tamper in alarm” & “tamper isolated” to STATUS message.

Added “tamper isolated” to isolate arm/partial SMS

Added firmware version to STATUS message

Changed Bell1 output to chirp using mini siren/strobe combo on disarm.

V7.70
-

Added extra checking on GSM modem to ruggedise comms

Recalibrated 24hr timer test

Changed the word “Line” to “PSTN” in status SMS

Improved GSM/SMS operation

Fixed partial arming via SMS with an entry/exit open....

... sms response may show tamper unsealed, rather than zone 1 or 2 open.

V7.68

Allowed arming while an entry/exit section is opened

V7.67

Added Tamper Isolate via User Code

Added Function 87

1 – Disable Tamper Input

2 – Tamper is Silent

3 – Tamper is active only when in On or Partial mode else if not selected tamper is 24hr

V7.66

Fixed chime operation

Improved line fail operation

changes in RF/GSM programming to improve swapping between modules

Updated RF key fob mapping

V7.54

Allowed pauses in GSM phone number

Removed arming chirps & strobe flashes on remote (keyswitch & RF module) for partial arming.

Removed exit delay beeps for partial arming

V7.53

Initial software release for IRIS8

Summary of Contents for iRIS8+

































Search results

Summary of Contents for iRIS8+

Reviews:

Related manuals for iRIS8+

Brands by name

Popular brands

MCM Electronics iRIS8+, Installer Manual

Search results

Summary of Contents for iRIS8+

Reviews:

Related manuals for iRIS8+

Brands by name

Popular brands