background image

0

TABLE OF CONTENTS

Air Filter  ....................................................................................................................................................................1

Fuel Filter  ..................................................................................................................................................................2

Spark Arrester Screen   .............................................................................................................................................2

Spark Plug  ................................................................................................................................................................3

Removal of Brake Assembly .....................................................................................................................................3

Removing the Chain and Bar ....................................................................................................................................4

Removal of Clutch and Drum Assembly ...................................................................................................................4

Removal of the Chain Oiler....................................................................................................................................... 5

Starter Servicing ........................................................................................................................................................7

Air Gap ......................................................................................................................................................................9

Flywheel Removal .....................................................................................................................................................9

Carburetor Removal ................................................................................................................................................10

Carburetor Adjustment  ...........................................................................................................................................12

Chain Tension Adjustment  ......................................................................................................................................13

Summary of Contents for MS1436NAV


















Reviews: