McCulloch CSE1835, Original Instructions Manual, Page: 19 / 288

L. EC DECLARATION OF CONFORMIT
Y
ENGLISH - 9
Husqvarna AB, S-561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Designation.................................
Chainsaw
Designation of Type(s).................
CSE1835, CSE1935S, CSE2040, CSE2040S
Identification of Series.................
See Product Rating Label
Y ear of Construction....................
See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
2006/42/EC, 2004/108/EC, 2000/14/EC, 2011/65/EU
based on the following EU harmonized standards applied:
EN60745-1, EN60745-2-13, EN55014-2, EN55014-1, EN61000-3-2, EN61000-3-11
Notified Body that carried out the EC type-examination
in accordance with article 8 section 2c....................... T
ÜV Rheinland LGA Products GmbH
Tillystraße 2
D-90431 Nürnberg
Germany
Certificate no.: ............................................................ BM 50268379
The maximum A weighted sound pressure level L
pA
at the workstation, measured according to EN60745-2-13,
is given in the table.
The maximum hand / arm vibration weighted value a
h
measured according to EN60745-2-13, on a sample of
the above product(s) is given in the table.
The declared vibration total value has been measured in accordance with a standard test method and may be
used for comparing one tool with another.
The declared vibration total value may also be used in a preliminary assessment of exposure.
Warning:
The vibration emission during actual use of the power tool can differ from the declared total value depending on
the ways in which the tool is used
Operators should identify safety measures to protect themselves that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time).
2000/14/EC: The Measured Sound Power L
WA
& Guaranteed Sound Power L
WA
values are according to the
tabulated figures.
Conformity Assessment Procedure............. Annex V
Ulm 12/02/2013
P. Lamelli
Global R
&D Director - Hand held
Keeper of Technical Documentation
EN 61000-3-11 Compliance statement
Depending on the characteristics of the local electricity supply network, use of this product may result in short
voltage drops at the instant of switching on. This may influence other electrical equipment e.g a momentary
dimming of a lamp. If the
Mains impedance Z
max of your electricity supply is less than the value shown in the
table (applicable to your model) then these effects will not occur. The value of the network impedance may be
determined by contacting your electricity supply authority
Type (CSE
____)
1835 1935S 2040 2040S
Dry Weight (Kg) 4.3 4.5 4.4 4.6
Power (kW) 1.8 1.9 2.0 2.0
Oil tank volume (cm
3
) 240 240 240 240
Maximum length of guide bar (cm) 35 35 40 40
Chain pitch (mm) 9.52 9.52 9.52 9.52
Chain gauge (mm) 1.3 1.3 1.3 1.3
Measured Sound Power L
WA
(dB(A)) 106 106 106 106
Guaranteed Sound Power L
WA
(dB(A)) 110 110 110 110
Sound pressure L
pA
(dB(A)) 95 95 95 95
Uncertainty K
pA
(dB(A)) 2.5 2.5 2.5 2.5
Hand / arm vibration a
h
(m/s
2
) 7.28 7.28 8.08 8.08
Uncertainty K
ah
(m/s
2
) 1.5 1.5 1.5 1.5
Mains-Impedance Z
max
(Ohm) 0.382 0.382 0.382 0.382