background image

 

 
 
 
 
 

 

Inspection Parts 

Inspection Items (

)

 

Clearance / Fit 

Scratches / Dirt / 

Harness Interference 

Installation / 

Tightening / 

Engagement 

Operation Check 

Negative battery 
terminal 

 

 

 

 

Driver-side door seal 

 

 

 

Driver-side A-pillar 
trim 

 

 

 

 

Driver-side inner / 
outer sun visor 
brackets and screws  

 

 

 

 

Sunglass holder and 
screws  

 

 

 

 

EC mirror torx screw 

 

 

            *1 

 

EC mirror harness 
connector 

 

 

 

 

EC mirror retaining 
clip 

 

 

 

 

EC mirror features: 

 

 

 

 

-  auto-dimming 

 

 

 

*2 

-  compass display 

 

 

 

*3 

-  HomeLink

®

 

 

 

 

*4 

User Guide 

 

 

            *5 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

The term of validity for this sheet:  3 months

 

 Inspection parts differ depending on the vehicle. 

 Inspect the installed / reinstalled parts for the following items:

12 

Inspection 

:  Applicable 

VIN:

Vehicle:

Approv

ed
 

Check

e

d

 

Person i

n

 

char

g

e

Date:                    /                    /

*1:  Tightened to 1.3 ft-lbs. (17.8 kg-cm). 
*2:  Mirror dims (key must be in ON position). 
*3:  Displays either "C" or directional heading (key must be in ON position). 
*4:  Red LED illuminates when each button is pushed (key must be in OFF position). 
*5:  In vehicle glove-box. 
 

 

Page 15 of 17 

 

9/1/2010 

Summary of Contents for 0000-8C-G21A


















Reviews: