background image

19

4. PROTECTIVE DEVICE

If internal heat builds up during operation due to 
clogging of the airflow orifice, if the machine is 
used in a highly heated environment or if an ab-
normality occurs inside the machine, the thermal 
protector for preventing burnout may be activat-
ed to stop the motor operation. The buzzer will 
sound in this case. In such a case:

1. Turn the power switch off and disconnect 

the power plug from the outlet.

For buzzer sounding patterns, see 
page 21.

2. Connect the power plug to the outlet and 

turn the power switch on to resume the 
operation.

If the motor has sufficiently cooled down, 
the resumed operation may active the pro-
tective device soon after. In other cases, 
the operation may not resumed when you 
turned the power switch on. In such a 
case, wait for about 30 minutes for the mo-
tor to cool down before restarting the ma-
chine.

3. If the protective device was activated 

when there were no apparent problems 
existing in the operating environment, 
stop using the compressor and send it to 
your dealer or authorized service facility 
for checkups or repairs.

OFF

  AC

110V

  AC

110V

WARNING

AKHL1230E_UK.fm  19 ページ  2008年12月10日 水曜日 午後6時4分

Summary of Contents for powerlite AKHL1230E

























Reviews: