background image

6

24. TURN OFF THE SWITCH WHEN THE 

COMPRESSOR IS NOT USED

When the compressor is not used, turn the 
switch OFF, disconnect the plug from the 
power source and open the drain cock to dis-
charge the compressed air from the air tank.

25. NEVER TOUCH THE SURFACE OF THE 

HIGH-TEMPERATURE SECTION

In order to prevent a burn, do not touch the 
piping, head, cylinder, motor and inverter 
case(lower cover).

26. DO NOT DIRECT AIR STREAM AT BODY

Risk of injury, do not direct compressed air at 
persons or animals.

27. DRAIN TANK

Drain tank daily or after 4 hours of use.
Open drain cock and tilt compressor to emp-
ty accumulated water.

28. DO NOT STOP COMPRESSOR BY PULL-

ING OUT THE PLUG

Use the " ON/OFF " switch.

29. WHENEVER USING THE HIGH PRESSURE 

SIDE OF THE MAX POWERLITE COMPRES-
SOR, THE GENUINE PARTS FOR THE MAX 
POWERLITE TOOLS, POWERLITE HOSE 
AND COMPRESSOR MUST BE USED.

30. REPLACEMENT PARTS

When servicing, use only MAX genuine 
parts. Repair should be conducted only by 
authorized service facility.

31. NEVER USE A TRANSFORMER FOR THE 

POWER SUPPLY OF THIS COMPRES-
SOR. USING A TRANSFORMER TO IN-
CREASE THE VOLTAGE WILL CAUSE A 
FAILURE OR BURNOUT. (IF A TRANS-
FORMER IS USED, OPERATION OF THE 
MACHINE WILL STOP.) 

32. NEVER CONNECT THE COMPRESSOR 

TO AN ENGINE GENERATOR OR DI-
RECT-CURRENT POWER SUPPLY

The compressor will break or be damaged 
from burning.

OFF

  AC

110V

AKHL1230E_UK.fm  6 ページ  2008年12月10日 水曜日 午後6時4分

Summary of Contents for powerlite AKHL1230E

























Reviews: