MAVIG CT Expres Service Manual Download | Manualshive

Page: 13 / 54

background image

Page 13 of 54

5100054

BND01O03.docx

8.3.

Service Life

It is of MAVIG’s utmost interest to satisfy our customers, and therefore we have carefully
tested and validated all our products. Consequently, besides the warranty period following
your purchase of new systems, please be advised that in case our products are properly
handled and serviced according to the then respective operation manual, we expect them
to have a lifespan  of 8  years as  of their purchase.  Without constituting any liability, we
strongly recommend that in order to continue to use our products after this 8 years’ period
you  should  have  them  inspected  according  to  the  then  valid  MAVIG  checklist  by  an
experienced technician at minimum on a yearly basis. If the product exceeds some wear
limits during such inspection, it will need to be dismounted and replaced. Failing to proceed
so  means  user  takes  all  responsibilities  in  case  of  failure/incident  related  to  the  MAVIG
Product.

8.4.

Information on the Identification Label

There are sales articles for each ceiling column and for the rest of the system:

Sales Article

Article Code

Ceiling Column 200 mm

GD40030CC00200

Ceiling Column 400 mm

GD40030CC00400

Ceiling Column 800 mm

GD40030CC00800

Extension Arm, Spring Arm, Injector Holder, Canopy

GD40300-BO

The system label for the sales article GD40030-BO is placed on the injector holder.
Furthermore, each component of the system has a component label:

«
...
11
12
13
14
15
...
»

Summary of Contents for CT Expres























































Reviews:

No comments

Related manuals for CT Expres

Brand: d&b audiotechnik Pages: 17

Brand: Ultimate Support Pages: 2

Brand: Rack Solutions Pages: 8

BudStackRack BSR-44-BT

Brand: BUD Pages: 2

Brand: Bora Portamate Pages: 20

Brand: Stein HGS Pages: 8

Brand: Fulterer Pages: 8

Brand: Innovative Pages: 2

Brand: Manhattan Pages: 2

Info-Tower Dual XL

Brand: HAGOR Pages: 16

Brand: NCR Pages: 15

Brand: Mustang Pages: 10

Brand: Sanus Pages: 18

clawFR 5 Degree

Brand: PanelClaw Pages: 24

The Original Arched

Brand: CATCHPOLE & RYE Pages: 5

Brand: CONEN Pages: 5

Brand: CONEN Pages: 7

Brand: CONEN Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands