background image

Delivery and transport

 

 

Page 8 of 27 

Delivery and transport 

Our implements are delivered in suitable packaging. Please comply with the valid occupational 
health and safety regulations when unpacking and use suitable hoists if necessary. 

4.1 

Delivery on a pallet 

4.1.1 

Lift the implement off of the pallet 

1. 

Remove the protective packaging and the transport safeguard. 

2. 

Lift the implement off of the pallet with a suitable device (crane or forklift) and set it 
down. 

4.1.2 

Long-distance transport 

If you want to transport the implement over longer distances (e.g. shipping via freight 
forwarder), you must lash the implement onto a pallet. 

 

 

The implement must only be transported in empty status without tractor! 

Do not unhook the material collection implement from the tractor in filled 
status. 

 

4.2 

Transport over short distances 

 

If the implement is not attached on a tractor, it must only be transported in empty 
status. 

 

Suitable transport equipment or hoists must be used (crane, forklift, lift truck) 

 

We offer wheel sets for many of our implements that enable safety and 
convenient transport over short distances. 

Please contact your sales partner for additional information 

Summary of Contents for CLS-G/H 1050




























Reviews: