matev CLS-G/H 1050 Operating Manual Download | Manualshive

Page: 19 / 27

background image

Maintenance

Page 19 of 27

6.2

Lubricating schedule

Lubricating points are marked with stickers. If a sticker is on a cover that can be dismounted,
then as a rule the lubricating nipple is under the cover.

Symbol

Meaning

1/d

Lubricate daily

1/50h

Lubricate every 50 operating hours

2/a (1/500h)

Lubricate at the beginning and end of the season and after
500 operating hours

Use a grease gun

Check oil level, top-up oil if necessary

Please comply with the instructions in the provided operating
manuals

Check oil level, top-up oil if necessary

Change oil ever x years.

Please comply with the instructions in the provided operating
manuals

Please comply with the operating manual provided for this
component. The lubricating intervals are specified in the
operating manual

«
...
17
18
19
20
21
...
»

Summary of Contents for CLS-G/H 1050




























Reviews:

No comments

Related manuals for CLS-G/H 1050

Brand: Nemco Pages: 13

Brand: Ecco Pages: 12

Brand: UMF Medical Pages: 12

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Sportsound SSR-200

Brand: Daktronics Pages: 5

Brand: DB Industries Pages: 60

Brand: vc999 Pages: 55

Brand: Salsbury Industries Pages: 4

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: IFM Pages: 175

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands