28 Fr
Garantie de remplacement
Garantie de remplacement
Cet article Mastercraft comprend une garantie de réparation de
trois (3) ans
contre les
défauts de fabrication et de matériau(x). Mastercraft Canada consent, à sa discrétion, à
réparer ou à remplacer toute pièce défectueuse sans frais au cours de la période de garantie
convenue lorsque l'article, accompagné de la
preuve d'achat
, est retourné par l'acquéreur
initial. Exclusion : usure ou bris causés par un usage abusif ou inapproprié.
Cet article n'est pas garanti s'il est utilisé à des fins industrielles ou commerciales.
SERVICE D'ASSISTANCE TÉLÉPHONIQUE SANS FRAIS : 1 866 220-2097
Soudeuse à dévidage de fil-électrode
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
IN972900AV 2/05
Operating Instructions & Parts Manual
WG2063, 58-8027- 4
Wire Feed
Arc Welder
Description
This wire feed arc welder is designed to
be used on standard 115 V household
current. The welder is equipped with
infinite wire speed control to accurately
select the proper wire feed rate needed
for various welding conditions. Internal
components are thermostatically
protected.
This welding system is designed for use
with flux-core or MIG wires. As delivered
from the factory, this welder can weld
with .024” (.6 mm) to .030” (.8 mm)
diameter wire in MIG
and
.030” (.8 mm)
to .035” (.9 mm) diameter wire in flux-
core. A starter spool of .035” (.9 mm)
flux-core wire is included.
COMPONENTS AND CONTROLS
1. Work Clamp: connects to workpiece.
2. Torch with .035” tip.
3. Power Cord: plugs into 115 V outlet.
4. Light: illuminates if thermostat has
automatically shut welder off.
5. Infinite Wire Speed Control: turn
clockwise to increase wire speed and
counter-clockwise to decrease wire
speed.
6. Heat Selection Dial: selects welding
power and turns welder on. Four
selections are possible: 1 – 2 – 3 – 4.
7. MIG/Flux-core Polarity Selection Dial:
for changing to electrode positive or
negative polarity.
8. MIG Gas Hook-up
9. Wire Feed Compartment
General Safety
Danger means a
hazard that will
cause death or serious injury if the
warning is ignored.
Warning means a
hazard that could
cause death or serious injury if the
warning is ignored.
Caution means a
hazard that may
cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.
!
CAUTION
!
WARNING
!
DANGER
See page 7 for supply cable
replacement instructions.
Unpacking
Welding accessories are packed inside
the wire feed compartment on the
side of the welder.
When unpacking,
inspect carefully for any damage that may
have occurred during transit. Make sure
any loose fittings and screws, etc., are
tightened before putting unit into service.
Report any missing or damaged
items by calling 1-866-220-2097.
CIRCUIT REQUIREMENTS
This equipment
requires a dedicated
115 V circuit. Refer to the following chart
for correct circuit breaker or fuse rating.
Do not run other appliances, lights or
tools on this circuit while operating this
equipment. Extension cords are not
recommended. Blown fuses and tripped
circuit breakers can result from failure to
comply with this recommendation.
!
CAUTION
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
Heat
Circuit Breaker or
Selector
Slow Blow Fuse
1-2-3
15 A
4
20 A
Fig. 1 - Welder Components and Controls
3
1
6
4
8
9
5
2
7
